Features:
Crown 160MA Mixer-Amplifier for Commercial Audio
The Crown® 135MA and 160MA are high value mixer-amplifiers for commercial audio. They provide 8-ohm and constant-voltage outputs (70V and 100V). Typical uses are paging, background music, and music-on-hold. The 135MA provides 3 inputs (each with a volume control) and a 35W amplifier output. The 160MA provides 4 inputs (each with a volume control) and a 60W amplifier output. Other features include priority muting, voice activated muting, phantom power, and Bass and Treble controls.
Features
- 3 inputs (each with a volume control), and one 35W amplifier output channel in 135MA
- 4 inputs (each with a volume control), and one 60W amplifier output channel in 160MA
- Ideal for paging, background music, and music-on-hold
- Balanced Phoenix-type mic/line input, telephone output, dual RCA stereo music inputs, screw-terminal speaker outputs
- Priority muting by VOX or external switch
- Bass and Treble controls on master output
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
< 0.5% at rated power at 1 kHz.–82 dB at 1kHz (Ch. 1 line input 0.8V,1V into 10 kilohms.15 VDC.0° C to 40° C–20° C to 85° C.Pushbutton on-off switch.Four controls, one perBass and Treble non-detentedBlue LED indicates power on.Green LED,Green LED, oneGreen LEDRed LED aboveDetented potentiometerDetachable IEC accepts US or4-position terminal3-pin balanced5-terminal Phoenix connector.Unbalanced line-level RCAtypeUnbalanced line-level RCAtypeUnbalanced4-terminalTrim pot adjusts level forDIP switch selection
Specifi cations
Frequency Response (at 1 watt from line out):
50 Hz to 20 kHz ± 1 dB.
19 Hz to 34 kHz +0, –3 dB.
Signal to Noise Ratio (ref. to rated power,
master volume at minimum):
Mic: > 58 dB.
Line: > 60 dB.
Telephone: > 60 dB.
Inputs 2 or 3 (and 4 in 160MA): > 78 dB.
THD + N:
< 0.1% at 5W at 1 kHz.
Input Sensitivity (for full output at maximum
gain):
Input 1: Mic 3mV, Line 800mV.
Input 2: 400mV.
Input 3: 400mV.
Input 4 (160MA only): 400mV.
Input Impedance (nominal):
Mic: 2.2 kilohms.
Line: 10 kilohms.
RCA: 10 kilohms.
Crosstalk:
Ch. 1 volume at minimum, other channel volumes
at maximum).
Line Output Level (nominal):
Phantom Power:
AC Line Voltages Available:
Universal Power Supply. Line voltage tolerance
+15%, –20%.
Operating Temperature/Humidity:
at 95% relative humidity (non-condensing).
Storage Temperature:
Front Panel Controls and Indicators
Power Switch:
Input Volume Controls:
input. Detented potentiometers with knobs.
Tone Controls:
recessed potentiometers under master output
volume control. Bass ±10 dB at 100 Hz, Treble
±10 dB at 10 kHz.
Power Indicator:
Input Signal Presence Indicators:
one above each channel's input attenuator, illuminates
when input signal exceeds –40 dBu.
Input Signal Clip Indicators:
above each channel's input attenuator, fl ashes
brightly at threshold of audible distortion.
Output Signal Presence Indicator:
above master output volume control illuminates
when any input signal exceeds –40 dBu.
Output Signal Clip Indicators:
master output volume control fl ashes brightly at
threshold of audible distortion.
Master Output Volume Control:
with knob.
Back Panel Controls, Connectors and
Indicators
AC Power Inlet:
Euro style power cords.
Amplifi er Output Connector:
barrier block with COM (Common), 8 ohms, 70V
and 100V terminals. Accepts up to 10 AWG terminal
forks. Non-touch cover included.
Preamp Line Out Connector:
Phoenix-type for connection to external amplifi -
ers. Level independent of master volume control.
Input Connector 1:
3 terminals for balanced signal, 2 terminals for
priority contact closure, which mutes other channels
when DIP switch 3 is on.
Input Connector 2:
connectors.
Input Connector 3:
connectors.
Input Connector 4 (160MA only):
line-level RCA-type connectors.
Telephone (MOH) Output Connector:
Phoenix connector (2 terminals for 1W output to
8-ohm speaker, 2 terminals for 600-ohm output to
PBX music-on-hold port).
MOH Level Control:
Music-On-Hold output from Telephone (MOH)
Output Connector.
Amp Confi guration DIP Switch:
for multiple functions.
1. On: Sets CH1 to Mic Input. Off: Sets CH1 to
Line Input.
2. On: Sets CH1 to Normal mode (no priority).
3. On: CH1 priority contact closure mutes other
channels.
4. On: CH1 VOX mutes other channels by sensing
signal through Input 1.
5. On: Routes CH1 to MOH output.
6. On: Routes CH2 to MOH output.
7. On: Routes CH3 to MOH output.
8. On: 15V phantom power.